Lake Elsinore, CA

Maintenance performed on Lennox system. Checked amp’s of blower motor and furnace itself, system using low amps. The filter was still clean and can be replaced next maintenance visit. The temperature split was in range to heat home properly. Coil is clean, and gas line is in open position. Turned heating off and checked through all electrical components. All components operating correctly. System is operational upon departure.

Arrived on site to perform diagnostic on system. Upon arrival homeowner states that his system has been running fine, but would like to have us look at it regardless. Cycled system for heating. Verified proper heating sequence of operations. Unit kicked on normally and started heating and heated the home with no issues until reaching setpoint. Checked system electrical and safety components. Did find that flame sensor was dirty and went ahead and cleaned it. Cycled system a couple times, unit kicked on normally very time. Gas pressure is set accordingly. All supply vents are open and filter is clean. No other noticeable concerns at this time. Signed up on maintenance program, reduced diagnostic to member price. System is operational upon departure.

Flue vent was broken off in the attic -I have pictures from when I left the job in September, showing how I left the furnace and it was still connected -I was able to pop the fitting back together. I also secured each fitting with metal strap and metal tape to ensure it does not come undone again -I also performed the dye search -The dye does not seem to be present at this time in the coil or the condenser -The standing refrigerant levels are also at the proper level, we will check the levels during our summer maintenance to see if anything has changed by then -As of now there is no noticeable areas of a refrigerant leak

90% furnace venting was leaking -PVC venting was not properly glued, condensate would leak out -The venting was also not installed to proper Goodman specs -There needs to be two 45°s fittings when piping into a Goodman furnace -There is currently a 90° fitting, which causes the condensate to pool inside fitting -New fittings were installed along with a reducer, and everything is properly sealed and glued

Thermostat calls for heating on both modes. Thermostat not energizing 0 wire. Jumped everything works perfectly fine .

Thermostat calls for heating on both modes. Thermostat not energizing 0 wire. Jumped everything works perfectly fine .

Thermostat calls for heating on both modes. Thermostat not energizing 0 wire. Jumped everything works perfectly fine .

Thermostat calls for heating on both modes. Thermostat not energizing 0 wire. Jumped everything works perfectly fine .

Performed maintenance on Nordyne furnace. Tested diagnostics, cleaned equipment, monitored operation.

Returned to replace pressure switch. Removed broken pressure switch and replaced with new unit. Tested pressure switch after installation and ensured furnace is operational.

Performed heating maintenance on 10 year old Amana unit. Cleaned return grate. Replaced filter with owner supplied FPR9 filter. Temperature rise is within limits. Cleaned flame sensor. Tested resistance of hot surface igniter. Tested all safety switches, found that a pressure switch that had fallen apart - I will be following up with Joe to replace the pressure switch. Tested all electrical connections. Joe would like us to see if we can get a humidifier unit that can replace the one he currently has installed on his system, a picture of the data plate is in the report. Upon departure the system is operational.

Performed furnace maintenance on 33 year old natural draft Carrier/Payne unit. Because of the age of the unit, after checking the temperature rise I removed the blower assembly to take a look at the heat exchanger. I sprayed the outer shell of the heat exchanger with soapy water to inspect for cracks. While looking in the burners I wasn’t able to find any water leaking into the inside, for this reason I don’t believe there are any cracks in the heat exchanger. While the blower was out I noticed it was very dirty and let Eddie know that this is leading to inefficiencies and the motor is not running as smoothly as it could. The secondary motor control measured at 1.2 mfd while it should be 5. Tested external static pressure and found it to be higher than manufacturer’s recommendation. This is due to it being an upflow unit in the garage and the inefficient duct design in the attic. The general condition of the ductwork was ok, meaning I didn’t see any tears or leaks, howe

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 30-60 needed, I got a temp rise of 38. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Replaced air filter for new air filter. Owner had extra one, so just used his. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 35-65 needed, I got a temp rise of 43. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Replaced air filter for new air filter. Owner had extra one, so just used his. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Performed diagnostic. Owner states system is not working correctly. He recently replaced thermostat. Found that thermostat was wired incorrectly. Rewired thermostat. Tried cycling unit and heat kicked on when calling for cool. Thermostat had to be reset and re-configured. System is operational upon departure.

Technician arrived to perform furnace tune up -Filter was replaced -Flame sensor cleaned off -Heating elements are all working properly -Blower compartment is clean -Burners lined up -Airflow is good -System is sealed properly

Technician arrived to perform furnace tune up for two systems -Filters were replaced, provided by homeowner -Flame sensors cleaned off -Blower motor were in rough condition, replacement was recommended to enhance life of furnaces -Compartment is clean -Electrical connections tightened -Heat rise for both furnaces were: 67 and 70 degrees

Furnace wasn’t heating or turning on when I arrived. I noticed thermostat was on wrong settings. I switched settings in menu option from Celsius to Fahrenheit. The system wanted to use aux heat and kept failing. After switching modes and setting system to heat. I got error code of flame sensor failure. I took out flame sensor and cleaned for a better connection to system. I put furnace doors on and system fired off. Heating works great and ready for winter.

Performed combo tune up on 2 year old AC Pro unit.

Arrived on site to install inducer motor

Upon arrival performed maintenance. System had a very dirty filter inside of system. Client handed me one to replace. Cleaned flame sensor as it had oxidation build up. Indoor motor & inducer motor are running in great condition. Checked ducting in attic, seems to be falling apart , advised replacing ducting system will help efficiency of entire heating & air system. Circuit board & electricals look good just extremely dusty. Thermostat in working order. Gas valve good. System is operational. Upon departure, home owner left. System is operational. Left tech sheet on table.

Upon arrival performed maintenance. System had a very dirty filter inside of system. Client handed me one to replace. Cleaned flame sensor as it had oxidation build up. Indoor motor & inducer motor are running in great condition. Checked ducting in attic, seems to be falling apart , advised replacing ducting system will help efficiency of entire heating & air system. Circuit board & electricals look good just extremely dusty. Thermostat in working order. Gas valve good. System is operational. Upon departure, home owner left. System is operational. Left tech sheet on table.

Upon arrival performed maintenance. System had a very dirty filter inside of system. Client handed me one to replace. Cleaned flame sensor as it had oxidation build up. Indoor motor & inducer motor are running in great condition. Checked ducting in attic, seems to be falling apart , advised replacing ducting system will help efficiency of entire heating & air system. Circuit board & electricals look good just extremely dusty. Thermostat in working order. Gas valve good. System is operational. Upon departure, home owner left. System is operational. Left tech sheet on table.

Upon arrival performed maintenance. System had a very dirty filter inside of system. Client handed me one to replace. Cleaned flame sensor as it had oxidation build up. Indoor motor & inducer motor are running in great condition. Checked ducting in attic, seems to be falling apart , advised replacing ducting system will help efficiency of entire heating & air system. Circuit board & electricals look good just extremely dusty. Thermostat in working order. Gas valve good. System is operational. Upon departure, home owner left. System is operational. Left tech sheet on table.

Arrived on site to perform furnace diagnostic on 18 year old York heater. Upon arrival client stated that he noticed inducer motor was not turning on so he went up in the attic and put pressure on one of the wire connections to the motor in it began spinning. After he let go it shut off, client sanded the connection and found that the copper wire has disconnected from the male electrical fitting. Began diagnostic and immediately found that copper connection was broken off as well put pressure and electrical connection arched. Inducer motor will have to be replaced in order through manufacture. At this time client is not interested in maintenance And would only like for the service of repair to be done. Client authorized for inducer motor to be ordered and is aware that this is the first component that will have to be fixed to get system running and it is unknown how other components may run. Upon departure unit is non-operational will have to return with new inducer