Fallbrook, CA

Arrived on site to perform maintenance on 1989 system. On arrival, homeowner stated that she needed a diagnostic and a maintenance. Advised that we would start with the diagnostic first to see what was going on with the unit, and then once the unit was operational we would perform the maintenance. Cycled system for cooling. Indoor and outdoor unit are coming on like normal, but system is not cooling. Performed diagnostic and thorough evaluation of system, findings are as follows 1. System is low on refrigerant. Homeowner recalled that she added refrigerant to the system about 7 years ago, but it leaked out the following year and hasn’t used it since 2. System uses old style R-22 refrigerant, which has been phased out. It is still available, but it is extremely expensive 3. Indoor blower wheel and motor is very dirty, and has been leaking a lot of oil 4. Ducting system is very old netting type of duct, and it is producing very poor air quality inside the home. 5. Homeowner develop

Quality control check

Performed AC maintenance/inspection on three system Rheem condensing units. During my maintenance I came across a few points of concerns They need to be evaluated and addressed. This will help maintain system Peak efficiency and increase longevity of systems Rheem 4 ton living area- 1. Found the compressor was pulling 20 A which is incredibly high when system is rated at 21.1 A 2. High voltage Relay responsible for starting system showing 12 ohms on low-voltage coil and pitting on contact points. 3. System pressures are adequate although indicating that there may be an air restriction causing coil to freeze up or be much lower in suction line temperature this cannot drop below 32 we are at 36 right now. 4. Single run capacitors taped together in weak on compressor side terminal in micro ferrets 5. Disconnect supported by fuses although not by surge protection 6. System contains our 22 refrigerant which was phased out January 1, 2020 Rheem 2 ton casita- 1. Found the contactor had abo

Performed maintenance and service for the cooling system. Replaced filter and measured indoor temperatures. Tested outdoor electrical equipment and rewired the compressor kit properly. Verified refrigerant charge. Tested starting loads and running amps for both motors, checked battery capacitance. Cleaned outdoor coil.

Performed AC maintenance on 4 ton Maytag condenser. During inspection found it for 10 a refrigerant pressures are low. System must have a leak search with leak dye/seal along with a charge up of refrigerant. Added 4 pounds of refrigerant along with sealant to system with return visit to confirm where leak is at.

Upon arrival performed diagnostic. Power distributor is not contacting fully to let power flow form one end to the other end of starter. It is pitted and burned. Secondary control is in range. Condenser fan motor is leaking oil. Older piece of equipment. Age 1997. Very minimum will get system up and running. Due to age and inefficiency recommend exploring options for replacement. System is non operational.

Upon arrival performed diagnostic. Power distributor is not contacting fully to let power flow form one end to the other end of starter. It is pitted and burned. Secondary control is in range. Condenser fan motor is leaking oil. Older piece of equipment. Age 1997. Very minimum will get system up and running. Due to age and inefficiency recommend exploring options for replacement. System is non operational.

Upon arrival performed diagnostic. Power distributor is not contacting fully to let power flow form one end to the other end of starter. It is pitted and burned. Secondary control is in range. Condenser fan motor is leaking oil. Older piece of equipment. Age 1997. Very minimum will get system up and running. Due to age and inefficiency recommend exploring options for replacement. System is non operational.

Upon arrival performed diagnostic. Power distributor is not contacting fully to let power flow form one end to the other end of starter. It is pitted and burned. Secondary control is in range. Condenser fan motor is leaking oil. Older piece of equipment. Age 1997. Very minimum will get system up and running. Due to age and inefficiency recommend exploring options for replacement. System is non operational.

Ac/furnace inspection

Upon arrival performed diagnostic on Goodman system. System had about 49 psi with a -12 sub cooling. Added 4 lbs of r410 refrigerant W/ leak dye & seal. System is now cooling at about 51 degrees out of every vent, 20 degree temp split. Will follow up with a return call to come out and look for leak. Customer paid In full. System was reset tested and fully functional.

Upon arrival performed diagnostic on Goodman system. System had about 49 psi with a -12 sub cooling. Added 4 lbs of r410 refrigerant W/ leak dye & seal. System is now cooling at about 51 degrees out of every vent, 20 degree temp split. Will follow up with a return call to come out and look for leak. Customer paid In full. System was reset tested and fully functional.

Upon arrival performed diagnostic on Goodman system. System had about 49 psi with a -12 sub cooling. Added 4 lbs of r410 refrigerant W/ leak dye & seal. System is now cooling at about 51 degrees out of every vent, 20 degree temp split. Will follow up with a return call to come out and look for leak. Customer paid In full. System was reset tested and fully functional.

Upon arrival performed diagnostic on Goodman system. System had about 49 psi with a -12 sub cooling. Added 4 lbs of r410 refrigerant W/ leak dye & seal. System is now cooling at about 51 degrees out of every vent, 20 degree temp split. Will follow up with a return call to come out and look for leak. Customer paid In full. System was reset tested and fully functional.

Cooling service and inspection

Repair damaged line voltage wire that shorted.

Repair damaged line voltage wire that shorted.

Repair damaged line voltage wire that shorted.

Repair damaged line voltage wire that shorted.

Sanitize and clean blower wheel

Air scrubber Installation to prevent dust buildup and disinfect all surfaces in home. Air scrubber install

System fan motor not working

Inspected the homes airflow relative to the heat pump

Replacing control board

Need to order circuit for unit. Not getting 120v for glow fly.