Fallbrook, CA

Performed maintenance on 15 year old package unit. Cycled system for cooling. Checked system electrical and components. Primary motor control is in good condition. Secondary motor control is in range as well but it is starting to leak some oil. Compressor amp draws are within range. Condenser fan motor amp draws are within range. Indoor blower motor was recently replaced and is in good condition. Pulled off condenser fan motor and thoroughly washed out condenser coil. Left homeowner replacement filter. Went over findings and recommendations with homeowner. Cycled system. System is operational upon departure.

12k BTU for main floor and 12k BTU for upstairs

Installation of a 5 ton Single Stage Bronze Package with ducting

Performed AC and Furnace tune up on 2 2 year old systems. Cycled systems for heating and cooling. Checked indoor and outdoor units electrical and system components. Temperature rise in heat mode is within range for both units. Heating components are all in good condition. Pressure switches and gas shut offs are working accordingly. Homeowner has his own Merv 11 filter replacements, both Filters were clean and did not need to be replaced on today’s visit. Checked outdoor units electrical and system components. Refrigerant levels are within range and systems are producing proper temperature splits. Primary motor controls are in good shape. Secondary motor controls are both in range. Amp draws for compressors and condenser fan motors are within range. Pulled off panels and thoroughly washed out condenser coils on both units. S30 thermostat is not displaying outdoor temperature. This thermostat was not installed by us. I tried resetting it and can not get the thermostat to display outdoo

RETURN FOR LEAK SEARCH. Checked for leak in evaporative coil. Checked for leak in exposed line set. Checked for leak in condenser coil. Found no leaks visible at this time. Informed customer that leak may come back or other leaks may form even though nothing was visible today. Previous customer had the same coil and there were 3 leaks in that coil. Customer understands. Customer is also on maintenance program. Unit operational upon departure.

Performed leak dye check on Maytag condensing unit. Upon my search I found no signs of leak de penetration anywhere within the outdoor condensing unit and evaporator coil. Leak that contains a sealant that may have plugged up leak location. System is holding pressure and is fully charged correctly. Applied and I log to service valve caps and King valve. System is fully operational and cooling upon departure

Upon arrival found motor not to be running when calling for cooling. Found motor wire to not be complete in tact. System was reset wired in correctly. System is operational.

Upon arrival found motor not to be running when calling for cooling. Found motor wire to not be complete in tact. System was reset wired in correctly. System is operational.

Upon arrival found motor not to be running when calling for cooling. Found motor wire to not be complete in tact. System was reset wired in correctly. System is operational.

Upon arrival found motor not to be running when calling for cooling. Found motor wire to not be complete in tact. System was reset wired in correctly. System is operational.

Installation of a 2 ton silver

Inspected system for faults and replaced faulty component. Tested system for functionality. Measured indoor temp splits and checked filter.

Installation of 4 surge protectors. Installed surge protectors on both heat pump units outside. As well installed surge protectors on both Air handlers in attic. Ensures LED lights are on and have protection. Cycled both systems in cooling. Both systems are operational and cooling after install. Both systems are operational upon departure.

Performed AC diagnostic on 2 1990s York condensing. Upon my diagnostic I found that the left side condenser of home was not working and right side was. Upon Further investigation many points and concerns were addressed. 4 ton left side of home- 1. Secondary motor control was blown on hermetic And fan side terminals 2. High voltage really burnt on contact points 3. Compressor pulling incredibly high amps 4. Condenser fan motor completely rusted and over amping 5. Compressor saver kit added to reduce start up amps of compressor 6. System contained R22 which is a completely phased out refrigerant as of January 1, 2020 4 ton right side- 1. Compressor pulling high amps on runtime. 2. Secondary float switch is being tripped due to primary clog 3. Compressor failing on start up amps adding compressor saver kit 4. System contains R22 refrigerant as well 5. Fan motor also not in good condition due to rust

Arrived on site to diagnose a no cooling 2002 rheem system. Condenser located in back yard. Furnace and evaporator coil located in attic. Spoke to client upon arrival she stated she’s tried to have home warranty come out but has had a hard time getting them out here. System has been down supine August 18. So had us come out. Upon arrival had client tune systems on. Indoor unit was operating. Found out door unit on to operational. Inspected both systems. Checked electrical compartment and components. Checked amp drawls and recorded reading for compressor, fan motor and Blower motor. Advised the summary of finds are as followed. Condenser 1. 2002 rheem system. 2. Found disconnect was set to off. Replace and system turned on but compressor shut off right away. 3. Primary control is completely burnt and pitted on contact points and is bad. 4. Secondary motor control is not weak and below range from compressor and fan motor working hard to turn on in past years. 5. Compressor will no

Arrived on site to diagnose a no cooling 2009 Goodman system. Condenser located in back yard. Furnace and evaporator coil located in attic. Spoke with client and stated about 3 days ago she notice she would run system to cool and few hours passed by and home was getting warmer. She want out side and noticed condenser system would not operate but indoor unit would. Inspect out door unit. Checked electrical compartment and components. Found system to be getting high and low voltage. Found secondary control good and in range. Found primary start control was actually bad and shorted out as a bug did get stuck in at point of contact and cause primary start control to fail. Advised I would need to replaced Bad components to get system operating and continue system evaluation. Client approved to replace starter. System is now operational. Checked amp drawls on compressor. Found start up amps are above max range as system has developed self wear over its 11 years of operation and from lack o

NO COOL/GOOGLE. Found system operational upon arrival. Customer stated unit was running with warm air and the previous owners told him it might need to be recharged occasionally. Upon inspection found unit running fine. After about 5 mins unit shut off. Found condensation line backed up. Customer stated he could clear it and redo some of the pvc pipe. Customer agreed to add maintenance agreement for 1 year. Unit operational departure. Customer will take care of issue since he was a mechanic for many years and is mechanically inclined.

Per Dave, return to replace txv. Pumped down system. Removed existing txv and installed new txv. Pressurized with nitrogen to ensure no leaks. Pulled vacumm down to 512 microns. Released refrigerant. Ensured system was charged correctly. Sealed up evap coil. System is producing proper temperature split, system fully operational upon departure.

NO COOL. Found system operational upon arrival. Customer stated that she ran system all day and the temperature was not dropping. She suspects it may have a pinhole leak. Upon inspection found system very low on charge. Informed customer of the possible leak but also due to the pressures and numbers on the gauges, it was possible there was an issue with the refrigerant flow valve. Customer approved adding freon and going from there. Added freon and system began to start cooling. Added charge to manufacture recommendations. Customer also approved leak search/leak seal at this time. Explained leak seal may seal the small pinhole leak but that if it doesn’t it will leave a trace behind for us to locate the leak. Customer ok with this. She also added one year esm to check system and also inspect for leak during those visits. Unit operational upon departure.

System cooling properly on arrival, found excessive condensation on the evaporator coil and condensate drain lines. Filter was completely clogged and the primary trap was clogged, this was cleared and filter was changed.

Tested cooling system and replaced filter. Measured indoor temperatures. Checked blower motor. Measured outdoor electrical loads and motors. Tested starting and run components. Checked refrigerant charge. Inspected ducting.

Tested system on the cooling mode. Replaced filter, cleared condensate drain. Measured indoor temperatures. Inspected outdoor condenser. Measured voltages and recorded motor loads. Checked battery cap and inspected fan motor, cleared debris from inside condenser, washed condenser coils. Verified charge.

Improved the slope of the primary condensate drain. Removed the water from the safety switch. Replaced the clogged filter. Tested the condensate pump. Disabled the “fan always on” thermostat setting.

Upon arrival performed circuit board installation. System is operational.

Upon arrival performed circuit board installation. System is operational.