Corona, CA

Combo Tune Up Performed- performed maintenance on 2020 Lennox system. Upon arrival system is working and operational. I began my maintenance at the outdoor unit by breaking it down and cleaning with water and solution. Removed heavy amounts of dirt and debris. I then inspected all electrical components for signs of wear and checked for tight connections. I measured amp draws and recorded refrigerant pressures. I then proceeded to the indoor furnace unit. Here I took temperature splits and measured static pressures. I inspected the condensate lines for proper drainage. I checked electrical components for tight connections and wear. Inspected the blower housing for balance and dust. Checked heating components for wear. Inspected heating components for proper operation. Filter has been changed at this time, home owner supplied. Upon inspection of both systems I found there to be no form of electrical protection, recommend adding surge protection to both systems to protect the sensitive el

Performed service call on a 2020 Lennox gas furnace. System is throwing error code 3. Flame is turning off 8-10 seconds after ignition. Flame sensor was cleaned with same issue. Ordering a new flame sensor to start, could be control board also. Installed surge protection today. Performed AC maintenance. Outdoor electrical components are in range at this time, refrigerant levels were checked and recorded. Outdoor unit was chemically cleaned. Needing to return with flame sensor and furnace maintenance. Furnace is not operational.

Arrived on site to perform fall tune up on 9 year old unit. Lennox unit located in attic. Client stated no issues and is good. Cycled heater and was good. Filter was replaced as it was really dirty as client home areas is in the hill and gets dust in home. Wheel is dirty from dust entering unit. Motor is good at this time. Inducer was good as well. Temperature rise was good. All safety switches are operational. Drain lines are dusty but clear. Either line has no safety overflow switches. Secondary line is draining into emergency pan and would like to stop that and add a safety over flow. Found air scrubber bulb to be bad and not being used as I advised her of it last time as well. Recommend replacing bulb kit or doing a buy back deal for a phenomenal air. Cycled unit and went over all findings with client and they are aware of system and how it’s running as well as recommendations. Client did hold off for now and would think about it and call us back if they want to move forward. Sys

Performed furnace maintenance on 1993 Day N Night furnace. System is original to home, has not been maintained in the past 10 years that he’s lived in the home. Cycled system for heating. Verified proper heating sequence of operations. Temperature rise across heat exchanger is extremely high, and furnace is extremely hot to the touch. Ductwork Is in very poor condition and is very undersized and restrictive, which is causing the high temperature rise. Inside of system is extremely dirty, as well as blower wheel inside the blower compartment. Amperages are normal. Unit has a lot of flame roll out. Heat exchanger can not be properly inspected due to a hard gas line that is running across the middle of the front of burner compartment, and blower wheel can not be pulled out due to attic configuration. System is extremely old and In very poor shape. Also condensation lines are clogged, and water has started falling through and damaged the ceiling. Went over findings and recommendations wi

Upon arrival performed maintenance on heating system. Indoor motor has some oil leaking. Blower wheel beginning to get dirty. Circuit board has some burnt terminals. No surge protection on system. Ducting is good. System has standard filtration. Cleaned inside of furnace cabinet and outside. Flame sensor clean. System is operational upon departure.

Upon arrival performed maintenance on heating system. Indoor motor has some oil leaking. Blower wheel beginning to get dirty. Circuit board has some burnt terminals. No surge protection on system. Ducting is good. System has standard filtration. Cleaned inside of furnace cabinet and outside. Flame sensor clean. System is operational upon departure.

Upon arrival performed maintenance on heating system. Indoor motor has some oil leaking. Blower wheel beginning to get dirty. Circuit board has some burnt terminals. No surge protection on system. Ducting is good. System has standard filtration. Cleaned inside of furnace cabinet and outside. Flame sensor clean. System is operational upon departure.

Upon arrival performed maintenance on heating system. Indoor motor has some oil leaking. Blower wheel beginning to get dirty. Circuit board has some burnt terminals. No surge protection on system. Ducting is good. System has standard filtration. Cleaned inside of furnace cabinet and outside. Flame sensor clean. System is operational upon departure.

6.99% 120 month (no pre-payment penalty) - $76/mo 18 month 0% - $364.50/mo

Platinum Furnace is included in this package equivalent to other companies gold furnace.

Performed heating maintenance on a 2019 Lennox gas furnace. Customer reports light use of the heating system due to the entire house being under construction. The thermostat had error code 532 which was fixed and cleared today. The customer provided a filter to be changed, existing filter was covered in paint and construction debris. Systems temperature split is ok. Sensors and switches were cleaned and tested. Blower wheel is clean and motor is amping ok. Gas valve and ignitor tested and recorded. Combustion blower is reading in range. Zoning was tested and is functioning well. System is not protected. The homeowners were. Briefed on the appointment. System was tested and functional st end of appointment

Performed furnace maintenance on 2000 lennox heater. Upon arrival homeowner stated that system has not been maintenance since 2019. I mentioned in the previous company was maintaining System although he was not satisfied with the work. Perform safety inspection on unit 1. Static pressure on the heater was 0.73 which is two times over the 0.5 it is rated for this is an indication of air flow restriction inside of the air duct system 2. System was tripping high limit switch due to clogged filter inside of 1 inch filter rack. Recommend filter swap every 1 to 3 months with a replaceable throwaway filter 3. Gas line is not equipped with drip leg 4. System is not equipped with surge protection in the case of a power outage thunderstorm etc. 5. Air scrubber bulb Is defective and burned out. Recommend catalyst is replaced to get air scrubber back to proper efficiency and sanitization of home Discussed and informed the full condition Charles 21 year old heater. At this time Charlie is not prepa

Arrived on site to perform fall tune up on a 2 2005 carrier units. Client stated no issues. They barley used heaters. Cycled both heater and good. Filter were dirty and replaced. Blower assembly and whee on both units were okay. Slight dust as it entered In past years. Both motors are amping in range. Both inducer motors are good. All safety switches are operational. Flame sensor and igniter are both good. Found both units with a high temperature rise of 50 on both. Static pressure was in range on both but a bit high on both units and advised client to findings. Due to high temperature rise and static pressure advised client would like to perform safety inspection of the heat exchanger. Client approved to pull main living room unit. Pulled heat exchanger out and inspect and found heat impingement and 3 chambers compromised due to cracks on chambers stress point. Showed client findings and advised unit is not safe to operate due to findings of over heating. Client is aware and stated h

Upon arrival performed maintenance. System was extremely dusty, client has a wood shop inside of his garage. Indoor blower wheel is very dirty. Supply ducting has no sealant at the top of plenum connection. Dusted off all electrical components. Temp splits in range. Static pressure in range. Amperages across system are in range. System is a 2018. There was no access to blow drains out. System has no saftey switches for condensate. Client is gonna duct seal his system. System is operational upon departure.

Upon arrival performed maintenance. System was extremely dusty, client has a wood shop inside of his garage. Indoor blower wheel is very dirty. Supply ducting has no sealant at the top of plenum connection. Dusted off all electrical components. Temp splits in range. Static pressure in range. Amperages across system are in range. System is a 2018. There was no access to blow drains out. System has no saftey switches for condensate. Client is gonna duct seal his system. System is operational upon departure.

Upon arrival performed maintenance. System was extremely dusty, client has a wood shop inside of his garage. Indoor blower wheel is very dirty. Supply ducting has no sealant at the top of plenum connection. Dusted off all electrical components. Temp splits in range. Static pressure in range. Amperages across system are in range. System is a 2018. There was no access to blow drains out. System has no saftey switches for condensate. Client is gonna duct seal his system. System is operational upon departure.

Upon arrival performed maintenance. System was extremely dusty, client has a wood shop inside of his garage. Indoor blower wheel is very dirty. Supply ducting has no sealant at the top of plenum connection. Dusted off all electrical components. Temp splits in range. Static pressure in range. Amperages across system are in range. System is a 2018. There was no access to blow drains out. System has no saftey switches for condensate. Client is gonna duct seal his system. System is operational upon departure.

int Inspection: Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration

Arrived on site to perform diagnostic on 5 year old Guardian unit. Homeowner states that upstairs unit is not cooling, is only blowing out room temperature air. Cycled system for cooling. Indoor and outdoor unit start up normally. System not producing temperature split at all. Gauged up to unit and found unit to be completely flat on refrigerant. Performed visual inspection of indoor and outdoor coil to try to locate leak but had no leak. Pressured lineset . Went into attic and can hear refrigerant leaking from the lineset but can not visually locate it do to location in the attic. System held pressure for about 10 minutes before going completely flat again. Leak needs to be repaired. Homeowner wants to hold off on repairs for now, as cooler temperatures are coming. No other work performed, system is not operational upon departure.

20 Point Inspection: Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration Homeowner will be ordering and replacing his own filters.

Arrived on site to perform diagnostic on 5 year old Rheem furnace. Homeowner states that the system is not heating correctly. It will run for about 1 or 2 minutes and then it’ll shut off. She then has to pull the thermostat off and then it’ll work for another little while. Cycled system for heat. System came on and started heating, but shut off after a short amount of time. System threw error code for high limit shutoff. Filter that was in the register was extremely dirty. Homeowner was also unaware that there was another filter inside the unit that had never been changed. Both of these filters were causing the unit to be restricted, and cut off on high limit. Removed both filters from system. Cycled system for heat. Furnace kicked on and ran normally until it reached desired setpoint. Advised replacing filters more frequently, and also removed filter from inside the unit as only one is needed. Unit does not have any condensation safety switch or surge Protection. Went over finding

Performed Ac maintenance on two system 1996 comfortmaker Units. Upon arrival client stated he just bought the house 6 months ago and would like to maintain the system to ensure the reliability and efficiency their system remains in a decent range. Ultimately System Is from 1996 and I did find multiple ok points of concerns that were addressed. 3 ton upstairs- 1. Disconnect has Melted internally. This was caused by a complete using too much power causing the wires to overheat resulting in the disconnect becoming brittle and melted. 2. Duel secondary motor control is becoming weak on hermetic side terminal 3. Compressor is locking out on start up. This is due to a failing compressor and a premature sign That the compressor can become defective at any moment. 4. Starter showed signs of pitting And burn marks on contact points 5. Condenser fan motor has significant oil leakage coming out of the bearing and can lead to it locking up or overheating 6. System Contains R22 refrigerant which w

Arrived on site to diagnose a leaking 2011 unit. Client stated water is leaking out of a vent. Upon arrival found a upflow unit in closet on second floor. A supply vent at time will leak water. Client stated she called a plumber and they told her to get a plumber to clear drain lines. They called us out and unit is cooling just there concern was the slight water. Inspected and looked at unit and found drain lines clogged up. Advised drain lines need to be cleared. Inspected how drain lines only found one drain line in use and no secondary line or any safety over flow switches. Found that drain lines did not run any where near drain line. The vent leaking water. Cleared drain lines after a cutt and clear to verify line went out side of home and under home. Cleared lines and clients saw that the HVAC is not what is causing water leak over there. They stated vent is directly replaced under master bathroom sink advised could be something else as a plumbing issues . Client saw and verifi

Arrived on site to diagnose a no cooling unit. Tenant stated unit need refrigerant and advised he would pay for repairs or diagnostic for today. Cycled unit and unit would run and shut off periodically. Checked pressure and found unit really low on charge as low side was at 27pgsi. Advised unit is low and dose use R-22 which is no longer in production and unit factory charge or 10 pounds. Advised unit is really low and due to age and how low advised a leak is present. Would need to charge up to get unit cooling good but there is. I warranty or guarantee on how long unit will coil for as it could leak out again. Checked electrical compartment. Tenant replaced secondary control for compressor. Stated he used a bigger one then the one used when he did originally replaced and he had replaced couple times in past. Advised not good. Primary starter is worn out due to being original. Going home warranty has been out and did repairs as well as they left a single secondary control for fan just

Arrived on site to perform spring tune up on a 2012 Lennox unit. Comedy located in back yard. Client stated no issues just wanted service and filter replaced. Cycled unit and operational. Inspected electrical compartment components. Found secondary motor control is weak and out of range. Recommend replacing at minimum to keep system operational. Fan motor was good and no oil at this time. Fan Moore is pulling 1.3 amps and max rated at 1.7 advised maybe reason why secondary is weak on fan side. Start up amps on compressor were in range but recommend adding a compressor booster kit to preserve compressor and prevent hard start up on unit. Run amps is pulling 8 amps and max rated at 16. Checked pressure and are good and cooling home at 20 degrees. No protection on unit. Cycled system. Inspected indoor unit. Found filter extremely clogged up blower assembly has slight dust due to dirt entered system in past. Drain lines are good and advised to keep on top of filter. Found purifying system