Aguanga, CA

Diagnostic on a 3 year old furnace. Got it back up and running on heat.

Cool Air Solutions

Performed a furnace maintenance on a Vexar system. Checked performance, temperature split, and blower condition.

Ac maintenance

Performed a hearing maintenance on a revolv system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filters where changed this visit. System was fully operational on time of departure.

Performed a heating maintenance on a 2021 Lennox system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filters where not changed this visit. System was fully operational at time of departure.

Arrived on site to perform furnace/heatpump maintenance

During my 20 point inspection, I Started off with hosing down condenser coil of any dirt and debris. Cleaned under compressor as well. Opened condenser cabinet and checked everything thoroughly. Starter (good), fuses (good), motherboard (good), dual secondary motor control (good), 24v (good), 120v (good), refrigerant levels sh 4, sc 2, osa 81, delta 29. Then went onto the furnace and checked furnace cabinet thoroughly. Blower motor (good), single secondary motor control (good), motherboard (good), 24v (good), 120v (good). House cools great and ready for summer.

Performed heatpump maintenance on one year-old Lennox. Maintenance checked out properly and surge protector was installed and registered. System was reset and tested upon departure.

Replaced two high limit switches on the furnace. Adjusted zoning supply temp perimeters. Monitored operation and ignition cycle. Measured supply temperatures and ensured system reached target set point.

Made airflow adjustments. Adjusted cfm zone settings, bled dampers. Added furnace condensate trap, measured gas valve pressure. Monitored operation.

Performed maintenance on ICP heating unit. Wiped down furnace with wet rag. Tested controls and measured ignitor. Measured electrical values and amp draws. Removed insulation foam and replaced with metal tape to reduce lost airflow at the evaporator coil lineset plate. Replaced 1” filters. Measured temperature rise. *cannot access ignitor / flame sensor due to bolt behind gas valve*

Upon arrival customer reports heating has been used often until this morning. Error code 38 and 223 were present. Heat pump mode works fine. Auxiliary heat was not kicking on. Found a moles plug was disconnected. System is operational at this time. Indoor protection and a filter were installed today.

Job walk

Collected a deposit of 3445 by check. Balance due will be 31005 due upon completion

Removed defective flare from the copper lineset and refitted connection with new flare. Used nylog thread sealant and tightened bolt. Pressurized system with 200 psi of nitrogen and leak tested connection with soap bubbles. Vacuumed system down to below 500 microns. Weighed in refrigerant charge with digital scale (3.10lbs) r410a. Tested system and measured indoor temps. Soap bubbles connection again, system is working properly at this time.

Replcad cap under warranty. Fan was not spinning

Replcad cap under warranty. Fan was not spinning

Replcad cap under warranty. Fan was not spinning

Replcad cap under warranty. Fan was not spinning

System has another leaking flare, attempted to tighten the flare but this flare is bad and needs to be cut and replaced. Charging the system at this time will just waste refrigerant. Need to provide a quote for a reflare on the outdoor unit.

Upon arrival performed warranty. Capacitor lead was not connected. System is operational.

Upon arrival performed warranty. Capacitor lead was not connected. System is operational.

Upon arrival performed warranty. Capacitor lead was not connected. System is operational.

Upon arrival performed warranty. Capacitor lead was not connected. System is operational.